一、排煙通風天窗是什么
排煙通風天窗也被稱為屋頂通風天窗、自然通風器、屋頂通風器、通風氣樓,是安裝在廠房屋頂的一種具有采光排煙、通風換氣作用的通風設備。
排煙天窗具有消防聯動控制功能,天窗窗框采用斷橋鋁材料,采光材料選用中空陽光板或安全玻璃,透光率高。加配雨感器、風感器、溫感器、煙感器等電子控制元件,在風雨天氣或溫度煙塵達到設置參數時,排煙天窗自動開啟或關閉,有利于排煙天窗自保護和廠房室內設備的安全。
二、排煙天窗的分類和作用
1、圓拱形屋面排煙天窗
最大開啟角度為45°,主要是用于經常啟閉通風的建筑當中,最大的特點就是保溫效果非常的好,而且排煙性能也非常的優良,也是最為普遍多見的一種排煙天窗方式。
2、一字型屋面排煙天窗
最大開啟角度60°、90°,多用于工業建筑,在采光、通風上面都可以能夠做到最好的體現,同時還能夠作為消防排煙的用處,也是一種非常不錯的天窗。
3、避風型屋面排煙天窗
最大開啟角度30°,適用于任何天氣情況都需要排煙通風的建筑,可避免出現飄雨、飄雪現象。
4、三角型屋面排煙天窗
天窗完全開啟時,排煙量最大,最大開啟角度為60°,三角型屋面排煙天窗窗體上面與安裝面成30°角,夏季有利于排水,冬季不積雪。
5、側開型屋面排煙天窗
最大開啟角度45°,適用于工業廠房的縱向天窗,是配合6米開間的鋼天窗架使用的窗型,天窗長度與鋼天窗長度一致,以6m為單位,洞口高度有1200、1500、1800、2400和3000mm五種,窗扇高度有150、600和750mm三種,可按洞口高度做窗扇的組合。
三、消防聯動排煙天窗的設計規范
1、消防聯動電動排煙天窗的選用,應當按照建筑要求的通風和采光需求,根據當地的氣候條件、主導風向、建筑物的高度、進排氣溫度、通風率和其他因素來確定消防聯動電煙窗類型,通常在設計的時候需要注意車間的面積,車間人員的密集度,車間散熱要求等等都必須考慮進去。
2、消防聯動電動排煙天窗≤1.0kpa,雪荷載≤0.4kn/㎡,每延米的軸承重量是150公斤/米。
3、消防聯動排煙天窗適用于非地震地區和地震烈度≤7度的地震地區,一些極端地區不建議使用消防聯動排煙天窗。
4、消防聯動式電排煙天窗適用于鋼結構建筑、鋼筋混凝土框架及棧橋結構建筑。由于安裝時主體框架是在不同位置連接的,所以在選擇通風排煙天窗時需要詳細介紹。如果用于鋼筋混凝土屋面結構,應在與鋼板相對應的連接處預埋,這是在屋面承重上考慮的。否則時間長了容易存在安全隱患。
5、消防聯動排煙天窗的鋼板底座是天窗與屋頂的連接部件,在設計消防聯動排煙天窗時,應充分考慮其性能參數進行設計和建造。
6、消防聯動電排煙天窗在安裝完成后的焊接骨架片應打磨并涂上防銹漆和底漆,并最好選用中性耐候漆。
7、在防爆車間等特殊環境中,在選擇消防組合式電排煙天窗時,一定要設計防雨設施,以保證問題的及時處理。
四、消防排煙通風天窗安裝方法
1、在屋頂的適當位置設置一個或多個與建筑物等高的固定支架,將防排煙系統管道通過支架固定在屋頂上。
2、在需要安裝的位置預埋金屬構件,并預留出相應的孔洞。
3、根據建筑物的實際情況及風壓要求確定風機型號和規格,并在金屬構件中穿入風管或電纜線。
4、將風機安裝在已預埋好的金屬構件上,并用螺栓緊固好各部件。
5、檢查各部位的連接情況是否松動,如有松動應及時擰緊;如發現機殼有裂紋、破口、碰傷等現象時必須更換新件后再進行裝配。
6、試運轉前應先啟動風機低速運轉3~5分鐘以檢查其轉向是否正確。
7、試驗結束后應對機組作全面檢查并進行必要的防腐處理后交付使用。
8、對裝有控制柜的機組還應按設計要求接好控制線路并接通電源后方可通電試運行。
五、消防電動排煙天窗的驗收標準
驗收時,首先應讓采光排煙天窗生產廠家提供消防電動排煙天窗電動控制箱和電動推窗器的質檢報告、CCCF消防認證證書。接著上到廠房屋面,觀察自動啟閉排煙天窗的外觀質量,如天窗是否完全關閉,是否存在翹起的情況,天窗是否平整,關閉時天窗的高度是否一致等等。
試運行工業廠房排煙通風天窗,觀察天窗在開啟過程中,電動推窗器與天窗其它部件是否存在交叉現象,務必排除這種情況,以確保天窗能正常工作。觀察天窗開啟與關閉過程是否流暢,必須確保每個天窗都完全調試好了。