雅格強光手電筒怎么拆

左手固定住強光手電頭部，右手轉動手電電池倉的蓋子。將電池倉后蓋擰下來后，可以看到里面的電池。之后左手按住強光手電，轉動將電池倉艙體，這樣就把電池倉艙體拆卸下來了。之后右手按住手電尾部，左手順時針轉動燈蓋，這樣就能把燈蓋拿下來，燈泡反光板可以用手直接拿出來，這樣強光手電拆卸完成。

雅格手電筒怎么換電池

首先，我們拿出一個需要安裝電池的小型手電筒。然后，我們把這個小型手電筒的后面給旋轉擰掉，就可以看到里面的電池了。然后，我們把這個里面的所有電池全部拆卸下來。再找到我們需要更換的全新電池更換上去。最后，點擊開關我們就成功地把小型手電筒的電池更換了。

該圖片由注冊用戶"品牌知識"提供，版權聲明反饋

雅格手電筒保養

1、存放時勿虧電

虧電狀態是指電池使用后沒及時充電。虧電狀態閑置時間越長，電池損壞越嚴重。

2、不要曝曬

不能在陽光下曝曬。溫度過高的話，環境會使蓄電池內部壓力增加，使電池限壓閥被迫自動開啟，直接后果就是增加電池的失水量，而電池過度失水會引發電池活性下降，加速極板的軟化，充電時起鼓、殼體發熱、變形等致命損傷。

3、定期檢驗

在使用過程中，如果放電時間內突然下降，很有可能是電池組中最少有一塊電池出現斷格、極板軟化、極板活性物質脫落短路現象。此時，應及時到專業電池修復機構進行檢查、修復。

4、正確掌握充電時間

在使用過程中，應根據實際情況把握充電時間，一般蓄電池都在夜間充電，平均時間在8小時左右。電池很快會充滿，繼續充電會出現過充現象，導致電池失水、發熱，降低電池的壽命。所以，蓄電池以放電深度為60%-70%時充一次電。

5、避免充電時拔熱插頭

充電器輸出插頭松動、接觸面氧化現象會導致充電插頭變熱，發熱時間過長會導致充電插頭短路，直接損害充電器，帶來不必要損失。所以發現上述情況時，應該及時清除氧化物或更換接插件。雅格手電筒推薦>>